wiring - Bathroom Fan/Light Combo - Home Improvement Stack …
2019年8月4日 · I am installing a new Bathroom Fan/Light combo to replace an older unit. The new one comes with 5 connections - 2 black and 2 white (one of each labeled fan and light) plus a ground. My wiring has 4 wires - 1 black, 1 white, 1 red and a ground. Need some advice on how to wire this properly. Thanks in advance.
electrical - Wiring a Heater, Vent Fan, Light for bathroom - Home ...
2018年10月24日 · Connect the black (fan) wire to the black wire in the /3 cable. Connect the blue (light) wire to the red wire in the /3 cable. Connect the red (heat) wire to the black wire in the /2 cable. Connect all grounds together (as always) Color-coding: Because the heat uses a lot more power than the light & fan, it gets the /2 cable.
bathroom - What wiring do I need for a fan/light/night-light …
2013年4月13日 · I just installed one of these combo fan/light/nightlight fixtures in my bathroom. We used a Leviton triple rocker switch like this one: We used cable with 4 wires between the switch and the fixture. The hot wire goes into the switch. The neutral connects to one of the 4 wires, the other 3 connect to the switch.
wiring - How do I wire new bathroom exhaust fan with light?
2020年10月13日 · There is 1 switch to control both fan and light. New unit has a white, black, and blue wire. Main wire in ceiling has a white, black, and copper ground. What do I do with the blue wire? I tried connecting with the black wires; light came on but fan did not. Instructions included with fan state to connect blue wire to red wire (shows going to ...
wiring - Connecting a bathroom fan/light combo? - Home …
2017年3月11日 · I'm replacing my old bathroom fan with a new fan/light combo. The new fan/light has four(4) wires, but the existing switch has only three(3) wires. How do I wire this set-up? There are white, blue, and black wires on the fan/light, and what I guess is a screw for the ground wire. But the existing switch wires are white, black, and a bare copper ...
Wiring a bathroom fan/light with only one neutral wire
2017年2月7日 · I bought a new light/ fan combo to replace and old one in a bathroom. This new fixture has those connectors that are plug and play, so to speak. You simply plug the appropriate color wire from the cable into the corresponding hole in the wiring harness for the fixture.
electrical - How to wire up a combined fan and light? - Home ...
2017年2月6日 · Using the type of connector pictured below makes it easier to try out connections to see which black is fan and which light (or some other funky combo - see instructions for fan/light unit). Otherwise you might be having to make and remake connections with wire nuts - which I suspect is annoying.
Help wiring a bathroom exhaust fan/light combo on a single switch
2020年6月13日 · The fan/light combo unit I am looking to install has a blue/white for the fan and a black/white for the light and a ground. I do not know if this makes a difference but the bathroom is a dual entrance bathroom and the old fan/light combo was able to be powered on both entrances (both single pole switches). Any help would be appreciated.
How to wire two switches to control bathroom fan/light combo …
2021年1月17日 · My bathroom has a light/fan combo fixture. The wall receptacle previously had: Single pole switch to control the light (on/off) Single pole switch to control the fan (on/off) Mechanical timer switch for the fan; There are only two 12/2 cables coming into the box (I assume one for fan, one for light).
electrical - Help wiring a Broan Heat/Vent/Light - Home …
2019年5月5日 · 1 - No indication that this is the only branch circuit in the bathroom or that it is supplying receptacles - i.e., no reason to jump to the "violating NEC" statement; 2 - permit - when/where that is required is location dependent; 3 - the device as a whole - heat, vent & light together needs a 20A circuit. Again, no indication that OP is doing ...