Using a shaper - FineWoodworking
2007年7月24日 · In essence, the shaper is similar to a router table. Usually, the knives are larger and the whole mass of the spindle and cutters makes a powerful sound. That alone makes many weak in the knees. There is no doubt this is a serious …
using a shaper in place of a router table - FineWoodworking
2010年2月1日 · iwas looking for a shaper,one of the few,the very few left in brooklyn, adviced steel city #48120. the catalog states "includes 3/4 & 1 inch spindles and 1/4 & 1/2 ROUTER collet standard ". steel city said the shaper can be used as a router table. the only reference i was able to find was finewoodworking #66 page 16, there is an equation i really dont understand as to the rate of feed due to ...
Router bit in shaper - FineWoodworking
2007年12月27日 · So it will be those helicopter bits (31/2 inch plus panel/hair raisers etc) which will work reasonably in a shaper but most router bits are of much smaller diameter than that-hence the need for the much higher spindle speeds found in routers when compared to shapers, and these will not produce good results in a shaper unless the shaper has some ...
Review: Shaper Origin's Trace - FineWoodworking
2024年1月30日 · The app includes tools for smoothing lines and deleting parts you don’t need, and sends files to any CNC, including Shaper’s Origin router. The industry’s first handheld CNC router, Shaper Origin, is delivering digital cutting capability to a growing number of hobbyists and pros. However, the design side of the process (creating the ...
Combination Machine NX-31 - FineWoodworking
2003年2月1日 · The machine is rated for a 12-in. blade, but the 12-in. diameter caused the splitter to sit so high that it couldn’t drop below the surface of the table (a clear saw-table surface is necessary when using the shaper). The machine accepts a dado head but doesn’t provide a throat plate to fit one, as the others do.
Tool Review: Shaper Origin CNC - FineWoodworking
2019年11月19日 · The Origin has a touch screen that controls a small trim type router motor with a 1⁄4-in. collet. The machine’s handles are comfortable, with an orange button on the left handle for retracting the cutter and a green button on the right that starts the cut and is the “Enter” button for various commands.
First Time Using a Shaper! - FineWoodworking
2008年6月17日 · I will be using a Delta shaper for the first time to run window and base board trim. I will be using a Delta power feeder as well. The trim is to be paint grade so I am using poplar. The profile is to be a duplicate from and 1840/60 Greek Revival home. The trim is approximately 2 1/4″w. by 1 1/4 thick The cutter blades have been ordered.
What machine is the most dangerous - FineWoodworking
2006年5月27日 · The spindle moulder (US shaper) almost certainly has the reputation as the most likely machine to cause injury. However, statistics in the US (and probably the UK where I am) indicate that the largest number of injuries occur whilst using the table saw.
Shaper cutters for template work? - FineWoodworking
2004年4月12日 · The solution I have for this was to buy an insert knife shaper body(3 wing) and have a local saw shop make me a rub bearing to match it. The initial cost was for the body, but the replacement 1 1/4" X 1 1/4" cutters are CHEAPER than sharpening.
Shaper Cutterhead - FineWoodworking
2004年4月3日 · This is a quick way to run a few feet of that special moulding. I would NEVER use this method on a table top machine.My heavy shaper has a spindle diameter of 1" Using the smallest diameter possible for the shape at hand,This machine at a speed of 10,000 R.P.M.Makes a loud roaring sound when started up. Scary,but safe when properly set up and used.