No power for handheld controller - Snow Plowing Forum
2016年12月11日 · Thanks for all the advice. Both controllers work because I tried them on the other dump truck and they worked. Dumb question, I did apply plenty of dielectric grease to the connections from the plow to the truck, could that be a problem? Another dumb question, how do I check the power at that remote connection? And yes, the truck was on.
snow way wired remote control | Snow Plowing Forum
2010年12月7日 · It is a wired controller, 3 wire, (gnd, 5v, and signal wire). The signal wire has the communication data to control the plow controller. There is a microprocessor in the handheld that communicates with the plow controller (serial channel). I think the controller/plow control has lost its program, something like the problem with the wireless system.
snoway plow remote issue programming wireless - Snow Plowing …
2012年12月2日 · so i bought a truck recently that had a snoway mt22 on it, I bought a used remote ( old one was broken per seller) I tried to pair the new ( used remote) last night, I followed the directions to the T from snowway, here are some issues i noticed that they don't explain:
Fisher minute mount no power to controller or plow - Snow …
2018年11月18日 · I was putting on my new plow for the first time last week. Same problem, turns out the wire from the ignition came unhooked. But then even tho I had power the plow didn't work. Went back to the beginning, retraced the attachment instructions, forgot to flip the switch on the tower to plow control. Thankful that all my problems that day wrre ...
Where to mount the controller | Snow Plowing Forum
2011年12月1日 · velcro'd everything that is always flying around the cab. phone, plow controller, stereo remote, i even put velcro on the console and the back of my notebook. 99 2500 Cummins- Boss V plow Mowers, blowers, shovels, and spreaders.
SnoWay Remote Control - Snow Plowing Forum
2004年9月20日 · It is a real fatigue saver since you can control the plow with either hand, while steering, shifting, etc. Typically, folks install the hard-wire control as a backup, though connections must be made on the older plows. On the new ones the control module must be swapped (about a 5 minute process). Buy it. You won't be sorry.
Controller flashing slow red "no communication" - Snow Plowing …
2018年9月19日 · Then I plugged everything in and checked again from handheld controller to plug A on plow module to confirm connections are good. 3. Installed new plow module 4. Confirmed 12 volts at plow module. 5. Switch is in plowing mode, even in attach/detach mode, I get nothing on the plow side to mount/dismount. It's pretty much dead on the concrete floor.
Sno-Way wireless remote battery - not impressed - Snow Plowing …
2014年2月15日 · Every time I use my plow the battery is dead in the wireless remote so I have to plug it in and it becomes a wired remote. The manual says charge it every 3 months, hell the thing won't hold a charge for 3 days. I went to my dealer and they replaced the battery. Different battery, same ****. From here it looks like a design problem.
Sno Way Controller Intermittent - Snow Plowing Forum
2021年12月29日 · Snoway controls, wireless, wired, remote, snow plow controls, pro control www.plowpartsdirect.com And, on older ones, some have just used the old meyer 2 switch set ups, and wired them in.
Western Handheld Control Has No Power | Snow Plowing Forum
2011年10月29日 · Hey guys, we have 3-6 predicted and I thought it would be good to go try out the plow. Western ProMount 8.5 on a Ford F-350 2008 V10 XLT, Got the thing all hooked up and went to power up the hand held controller and no power.