p28 ecu??? - Honda Civic Forums
2010年9月25日 · These are OBD-1 ECU#s: P05 - Civic CX - D15B8 P06 - Civic DX - D15B7 P07 - Civic VX - D15Z1 SOHC VTEC-E P08 - JDM Civic (EG4) 1.5l SOHC VTEC - D15B P28 - Civic EX/Si 1.5l SOHC VTEC - D16Z6 *Note that this ECU has also been used with the D16Z6 and the B16A in the US. P30 - DelSol Si/Civic SiR (B16A DOHC VTEC)
P28 ECU? | Honda and Acura Car Forums
2006年5月3日 · The p28 is a 92-95 SOHC vtec ecu. It is widely used for tuning many different honda vehicles and setups when chipped. The rom inside your ecu has a different fuel/ignition curve than that of the stock settings.
OBD1 Honda ECU pinouts - Honda and Acura Car Forums
2005年3月27日 · These are the pin designations for the OBD1 ECU as well as their wire color and voltage. I always have a hard time finding this information when I need it as I'm sure others do, so here it is KEY: (voltage values measured in DC Volts unless otherwise specified) V = Volts Wht = White Blk = Black Grn = Green Yel = Yellow Brn = Brown Blu = Blue ...
92-00 Honda Engine Swap Wiring Guide VTEC AND NON VTEC
2011年10月8日 · (note for all 92 Civics the VTEC is already ran on the shock tower to ECU harness so using an EX/SI 92-95 engine harness will make VTEC plug and play.) D16Y8 using P28 EX/Si/VX - D16Z6/D15Z1 Mostly plug and play. VTEC plug and play. Knock sensor will not be used for the P28 ECU. The EX/Si/VX distributor will not bolt up to the Y8 head exactly.
Honda Civic: How to Identify Your ECU - Honda-Tech
2015年5月18日 · On all fifth and sixth generation Honda Civics, the ECU is located behind the kick panel in the front passenger's side foot well. To remove the ECU and view its bar code label, use a ratchet and socket to unbolt it from the sidewall. Disconnect the wire harnesses of the ECU before completely removing it. Figure 1. Honda Civic's ECU location.
Will p28 ecu work with JDM b16a - Honda and Acura Car Forums
2005年10月11日 · The P28 will run the engine fine. you just need to get it chipped. If you dont want to get it chipped then buy a P30. As a matter of fact a pr3(obd1),pr4(obd1), p05,p06,p07(1720 board not 1560), p09, p28, p30,P61, P72, and P75 will all run the engine perfectly as long as they are chipped with the right code and the non vtec ecus are modified to ...
FAQ: D15 SOHC VTEC Mini-Me : Massive Write-Up (56k Goodbye)
2003年7月5日 · The P28 ECU plugs right in, you all you’ll need to do is wire the VTEC up. First, you’ll need to get an engine plug from a junkyard for the VTEC solenoid oil pressure. You’ll need to run the blue wire (or whichever color is from the plug) to pin D6, and then run the black ground wire from the plug to anywhere on the motor.
P28 ECU? - Honda and Acura Car Forums
2010年5月11日 · I just bought a 1997 Honda Del Sol Si, and the I'm looking to tune the ECU. I looked online for ECU identification numbers and all. The number on ECU is 37820-P28-A04, which from what I've read is a OBD1 ECU, but my problem is, it's not OBD1, its OBD2A. I searched and couldn't find any OBD2A P28's, So what do I have, and can I install a Hondata ...
B16a2 p28 ecu - Honda Civic Forums
2011年10月22日 · Secondly are there any advantages with using a p28 as apposed to a p30 I have pieced together bits of information and always believed that the p28 was a bit more versatile than the p30 but after reading some posts in this section of the forum i am under the impression that the p28, p30 and a few others are all more or less the same.
p28 vs p73? | Honda and Acura Car Forums
2009年5月9日 · p28 is a 1.6 SOHC Vtec ecu, unless its chipped out and tuned, dont run it, you'll just run lean and piss on your motor.. p73 is a USDM itr ecu, which should do you fine, until you get tuned. DD TECH(DDTECHCAMS.com) - Round 2 Motorsports - Myers Manifolds - YCU - AFITurbo - Sheepey INC - Phearable.net - SpeedTrapp Consulting