My G4000 lathe: Fun and frustration | The Hobby-Machinist
2006年2月1日 · Still the 41T gear turns to sludge. One hope I have, 15 years later, is that Grizzly found this to be a recurring issue with the G4000 and have remedied it with a better version of the apron. And indeed, if I look up the parts, I see that the description for the apron says Grizzly P4000701 - APRON CASTING V2.01.06 (notice the V2.01.06). I have ...
Grizzly G4000 | The Hobby-Machinist
2013年4月24日 · Spindle bore is larger, spindle nose threads are more “standard” (1 3/4” x 8tpi) than on the G4000 (39x4mm). Spindle has MT4 taper, tailstock MT3 (vs MT3-MT2 on the G4000). The G0602 has a chuck retainer on the spindle. And finally, the G0602 comes with a “genuine” 4-jaw chuck, unlike the “glorified faceplate” you get with the ...
G4000 ELS Upgrade - The Hobby-Machinist
2021年10月22日 · Back around 2005, I purchased my Grizzly G4000 Lathe and did quite a few very useful mechanical mods to it, leading to the publication with the help of others, two FREE handbooks "Tricking out the Asian 9 x 20 Lathe" and "Rebuilding The Asian 9 x 20 Lathe". Well, this lathe has served me well and continues to do so.
6 days to decide G4000 9x19 vs G0602 10x22 Both around $1500 …
2020年3月25日 · For gears the the G4000 has a 9 position lever, the G0602 has two, 3 position knobs so both have 9 speeds just differ in how they get there. You will be using change gears on both for the full range of threading and will need to move the …
New Grizzly G4000 9x19 setup | The Hobby-Machinist
2024年1月30日 · Hi folks, many thanks for the great info others have posted on this forum. I have a new Grizzly G4000 9x19 lathe on order to set up in my garage shop. Planning also to acquire one of the LMS 3786 tooling packages for it. For the bench this will sit on, initial thoughts are to set the spindle height at 45" from the floor, elbow height.
Grizzly G4000 lathe backorder advice | The Hobby-Machinist
2024年1月26日 · Wasn't sure if this was the new "normal" of current supply chain issues. I ordered a G4000 9x19 lathe on January 20. So far Grizzly has advised timing as: - On 1/24: Warehouse receipt 2/25 with delivery shortly thereafter - On 2/7: Warehouse receipt 4/2 with delivery shortly thereafter
Quick change tool post for G4000 Grizzly lathe - The Hobby …
2020年11月18日 · My small machine is a Grizzly G-1550. The only difference of note is the 1550 has imperial threads where the G-4000 has metric. The 1550 is from Taiwan, the 4000 is from mainland China. . .
Handy mod for G4000 9x20 lathe | The Hobby-Machinist
2013年2月17日 · Luckily, the G4000 uses a very small section belt, so the grooves in the pulley aren't very deep. I solved the problem by drilling a 1/4" hole through the pulley, centered 1/4" inward from the outer edge. The hole is large enough to allow access to the lube point, but small enough that it doesn't break into the belt groove.
G0768 Or G4000? | The Hobby-Machinist
2016年1月17日 · The start of that was Bob Bertrand (Lathemaster), who first imported the 8x14 lathe about 15 years ago and gained quite a following who claimed it was more rigid than the 9x19. 2. Yes, the 8x16 has no QCGB. But the partial QCGB on the G4000 still requires a lot of gear swapping. 3. The DC motor on the G0768 will give you less vibration. 4.
First Lathe - G4000 vs. G0768 | The Hobby-Machinist
2014年11月13日 · I am looking at either the G4000 or G0768. I started looking at smaller 7X14 lathes but I'm worried about buying too small now and regretting it later. Here is a general idea of where I sit on things: G4000 Pros-Seems to be a very common machine, lots of info out there-A lot of threading options (although not really a huge benefit for me)