Table 2. Configurations of Cisco Catalyst 2960 Series Switches with LAN Base Software Cisco Catalyst 2960 Switch Model Description Uplinks Available PoE Power 1 Gigabit Uplinks with 10/100 Ethernet Connectivity Cisco Catalyst 2960-48PST-L 48 Ethernet 10/100 PoE ports 2 one Gigabit Ethernet SFP ports and 2 fixed Ethernet 10/100/1000 ports 370W
2960 will not allow "switchport trunk encapsulation dot1q" CLI
2014年3月2日 · I have a Cisco 2960 switch that is not allowing me to setup switchport trunk encapsulation dot1q on a trunking interface. The show capabilities shows that the interface can use 802.1q, but when I try to CLI the command the work encapsulation is not an option. Please advise with a solution. Thanks, S. Model - WS-C2960G-24TC-L
Cisco switch 2960 - 7port - POE issue - Cisco Community
2011年11月13日 · hi, when am trying to plug a PC into the switch, it takes power as the switch is POE . but when trying to plug IP Camera Device it does not take any power. although i have cisco 2960 - 24 ports both PC and IP Camera getting power. while troublshooting by #show power inline , i get nothing as well....
Solved: How to disable Telnet and enable SSH - Cisco Community
2016年8月1日 · Hi, on a 2960-S I found that SSH was not enabled, or at least not properly configured. I only could login via console and telnet. The one and only thing I changed then in running config was to add "transport input ssh2" to the section "line vty 0 4". But what happens now is that I cannot login via t...
Cisco Catalyst Switch 2960 with unmanaged switch
2010年12月21日 · I have cisco switch 2960 and a unmanaged switch etherwan. please find the attached datasheet for your reference on the unmanaged switch. Now i using SPF module (Fibre) to connect the Gig port to the Fibre port of the unmanaged switch. The port of the unmanaged switch is not an Gig port it is 100Fx. ...
Trouble finding OIDs for 2960x switch - Cisco Community
2018年11月30日 · I have a stack of 2960x switches are I am monitoring them using OID values. However, I am having trouble finding the OIDs for the individual switches in the stack.
Switch: How to test a cable status? - Cisco Community
2013年8月7日 · switch#sh ip int bri | i up. GigabitEthernet0/1 unassigned YES unset up up . switch# switch#test cable-diagnostics tdr interface gigabitEthernet 0/1. TDR test started on interface Gi0/1. A TDR test can take a few seconds to run on an interface. Use 'show cable-diagnostics tdr' to read the TDR results. switch#
power up cisco 2960 switch with 12V DC Power
2019年3月7日 · hi all , I have some issue with supply power to cisco 2960-24TT-L switch. In my server farm rack is having DC current of -48V. But however cisco switch require 12V DC current. Cisco Spec. Cisco Catalyst 2960-24TT-L 12V at 5 A 5 A How can I power on
Commands to find mac-address and IP on a port - Cisco Community
2016年6月7日 · For eg. on Cisco 2960G switch. c2960#sh mac address-table interface gi0/3
Solved: 2960 switch passthrough switch - Cisco Community
2010年11月9日 · So the question is the 2 servers each requires a tape drive, has a management console and then your normal NIC card so each server will require 3 connection. Do I need to buy 2 seperate 2960 switches or can I. use one 2960 and configure 2 vlans on them and use it as a pass through switch to the core switch.