Anyone using/install an Air Scrubber Plus? - Love Plumbing
2018年3月28日 · On the Activetek website, they do not have an "Air Scrubber Plus"; they have the Induct 2000...that looks EXACTLY the same. Then I looked up the manufacturing location in VA and I get another name - Aerus (former Electrolux company). I look into Aerus and the claim they are headquartered in Dallas, TX, with manufacturing in Bristol, VA.
Need Ballast for Aerus Air Scrubber - Love Plumbing & Remodel
2020年9月14日 · I have an Aerus Air Scrubber model A1013C. I need a replacement ballast. Aerus will not sell direct. I have to go through an HVAC installer. I have contacted three and they will not sell parts. They will sell me a new unit and install it, but there is nothing wrong with my unit except the ballast is shot.
Bosch Combi Boiler keeps overflowing - Love Plumbing & Remodel
2024年12月27日 · Take a pic of boiler and related piping including the pump and ex tank. The ex tank air pressure has to match water pressure with heater and pumps have to off and 100° or cooler water. Tools needed 0-50 lb tire gauge, hand tire pump or air compressor. If using a air compressor short bursts and check pressure. Valve opposite piping end.
Opposing P-Traps | Terry Love Plumbing Advice & Remodel DIY ...
2025年1月2日 · No, p-traps are never in series. There is an allowance in the IRC/IPC to do what you propose (attach a utility sink to a laundry standpipe) without a trap outside the wall.
Riello burner not coming on automatically when indirect hot water ...
2024年11月12日 · Our 10+ year-old Buderus has a Riello burner that was replaced about 2 years ago. It has been working fine but I hadn't scheduled a flue clean-out in that time, or a nozzle replacement, so I signed up with a local long-established company to do it, different from the company who installed the...
How to Bleed Air from Navien Combi 240? - Love Plumbing
2019年1月8日 · With the tank disconnected from the plumbing, pump the air to the target system pressure plus 1-3 psi. eg: If the system's water pressure is set to 13 psi (at idle, not when hot at the end of a burn) set the air pressure in the tank to 14-16psi, not more, and not lower than 13 psi. Then re-install it.
Softener introducing air into my water lines | Terry Love Plumbing ...
2010年2月12日 · Why the air problem stopped when the unit was put into by pass may be due to an air leak in the bypass valve when it is in the service position. Or the volume of water used for a regeneration is causing the pump to suck air; or if there is a jet pump which can suck air but not leak water at a loose fitting.
Moving a bathroom in the basement - Love Plumbing & Remodel
2017年4月5日 · I'm pinging for opinions on a basement bathroom project. Full gut and remodel of my basement, air seal and insulate and a bunch of other stuff. The original bathroom rough-in is in a bad spot - roughly center of the space (total basement is about 1000 Sq/ft). It's an ugly eye soar and just doesn't flow well.
Air Gap and Air Admittance Valve (AAV) - Love Plumbing & Remodel
2015年7月2日 · The air gap is always legal and code approved. There is another way to prevent siphoning that many of us use that is code approved in many places. That is the "high loop" method. That simple required the drain hose is looped above the top of the washer.
Okay to blow out sprinklers through Backflow?
2020年9月7日 · Do do blow air into any test port on the device. Here is Febco's procedure for drainage and freeze protect. You do need air but the connection needs to be past the preventer. On the diagram it would be a location "E" and there should be a …