How to Fix a Wooden Garage Door Panel - Woodworking Talk
2019年4月10日 · You can take steps to repair your garage door without ordering an expensive custom replacement door. Steps to Replacing a Rotted or Damaged Garage Door Panel It's common for the bottom panels of a wooden garage door to begin to show water or insect damage, but you can learn to replace the individual panels of a garage door. Here's how.
Wooden Garage Doors - Woodworking Talk
2007年9月13日 · Then have a garage door installer install the door when you are done, unless it is something you have been trained to do. Springs can kill or maim, don't under estimate them. One other thought, the garage door manufacturers make a lot of carriage style doors in steel if you don't have to have wood. Virtually no maintenance once they are installed.
Custom Wood Carriage Garage Door, How to Refinish?
2012年8月18日 · It is only about 1000 psi and won't damage or roughen the wood other than being wet. If you used one that is 3000 psi or more it would roughen the wood by eating away at the soft part of the wood. After the door is stripped the areas that have mold I would use a little bleach on to kill it. Then once the door is dry it could be sanded and finished.
Large cabinet doors. How to avoid warping | Woodworking Talk
2022年6月16日 · I'm constructing it like a kitchen cabinet with 2-1/2" wide 3/4" thick rails and stiles. I'm worried a door that big will be in danger of warping. I plan on doing mid-rails and plywood panels between the styles instead of solid wood with the hope that these items will help reduce the danger of warping. I had also thought of slicing the stiles ...
Garage Door Panels - Woodworking Talk
2014年3月1日 · Woodworking Forum. General Woodworking Discussions
router table/shaper for raised panel doors? - Woodworking Talk
2007年8月11日 · i was in the same boat as you about 4 years ago.i went to a wood working show and bought a 3 piece CMT raised panel bit set.It had bits for your rails,stiles and panels.When i make a door if it be paint or stain grade,i use my pocket hole system jig (Kreg tools). i miter the corners and pocket hole one on each corner,then pin nail corners.The bit that routers out the …
Door panels rattle - Woodworking Talk
2016年6月6日 · I have made hundreds of cabinet doors in my lifetime and never had a problem but the most recent batch I made has rattling panels. The groove in the rails/stiles is 1/4" but the 1/4" panel (sheet goods) is really about 1/32" thinner. I expected the rubber strips (CMT panalign) to keep the panels from rattling but such is not the case.
How do I remove stain from exterior front door - Woodworking Talk
2010年9月4日 · JMO. That doesn't mean with some technical help and physical help, to remove the door and seal the opening either with visqueen or a temporary plywood door, you can't do it. Sanding off the old finish by hand will take for ever and unless you can lay the door flat and see what you are doing and have gravity working for you, it will be very ...
How many amps for garage shop subpanel - Woodworking Talk
2021年4月4日 · A garage shop is physically limited on the size, so the only thing you have to worry about are the big-ticket items, and whether they might exist. Aside from the large specialty items (I'll get to those later), a typical garage workshop can operate on …
How to best lubricate wooden moving parts - Woodworking Talk
2009年9月15日 · I have made small wooden toys out of 2x4s and 1x4 for years. I melt candle wax over the axles and then hold the candle under the axle and melt the wax into the wood. The dry dowels soaks up the wax. I do this twice per axle. The little cars and truck will roll all the way across a room with little effort.
跳至内容