Idler Pulley Bearing Replacement Info - Nissan Forum
2003年5月15日 · for those who ever have an idler pulley fail, u can replace it with a new bearing rather than buying the complete assembly from the dealer. the oem bearing in the pulley is a NSK. the part # on this bearing is 6301DULX. any good auto parts store can cross reference this bearing and find a replacement for much less $ than the complete assembly.
Belt noise: replace idler pulley? - GA16DE | Nissan Forum
2008年10月5日 · I suspect the idle pulley need to be replaced. The noise is like 'sho----- sho-----sho' at idling. When I give gas, it becomes 'sho-sho-sho'. Also, the back of the belt and pulley surface are shiny, suggesting they are polishing each other. The only pulley touches the back of the belt is the idling pulley. A/C on or not doesn't change the sound.
How to replace power steering idler pulley 2000 3.3 v6...
2012年3月13日 · I'm about 99% sure it's the idler pulley for the power steering pump, because the belts are in good shape, tight enough (1/2-3/4" play), and the AC idler has been replaced. I see the belt tension adjustment bolt on the power steering pump area - to the left on the same bracket/bar that has the one for the AC idler
Torque Specs? - Nissan Forum
2005年5月8日 · Crank Pulley Bolt - 97.7-112.1 ft-lb Idler Sprocket Bolt - 31.8-42.7 ft-lb Intake Cam Sprocket Bolt - 72.4-94.0 ft-lb Exhaust Cam Sprocket Bolt - 31.8-42.7 ft-lb The oil pan diagram on the first page of the Oil Pan Section has the torque specs for the bolts: Oil Pan Bolts and nuts - 55.6-73.8 in-lb (note INCH-lb) Lew
a/c compressor - Nissan Forum
2007年5月23日 · Run A/C and listen for squeak, turn off A/C, if squeak is gone it is your bearing. How to change is another thread If not is probably one of the other two. Check belt tension and for wear such as cracks, if worn replace. Idler pulley check - Loosen belt and slip off of idler pulley, spin pulley by hand to see if pully is good. Hope this helps ...
Belt or pulley squeal on cold starts? - Nissan Forum
2007年1月24日 · The squeal you are hearing is the belt slipping in the pulley. On cold mornings, the belts are not as soft and "sticky" as the are when it is warmer. The belts will slip over the surface of the pulley causing a squeal. Once the belt warms up, it again engages the pulley and the squeal goes away.
1998 Altima Idler Pulley | Nissan Forum
2008年1月1日 · After you remove the belts look closely theres 3 bolts that hold a plate mounted to the engine block that holds the whole idler pully assembly. remove those 3 bolts and the plate and the pully will clear the sidewall and you'll be able to pull it from the engine bay! you may have to jack the engine up slightly.
New to board, timing chain issues | Nissan Forum
2010年9月2日 · hi, i too am new to your forum and i am also having some issues with my xtrail 2liter petrol 2WD 2005.i bought it at 120 000kms it is now on 140 000kms.recently i have a cluttering noise at startup which lasts a few seconds. as if the timing chain assembly lacks oil and once oil pressure is reached then noise disappears.firstly i did an oil change so for a couple of …
P0402 OBD-2 Trouble code | Nissan Forum
2007年8月13日 · I think when you say "condensor," you actually mean "compressor." The condensor is the part that sits just in front of the radiator. The compressor is the part that bolts to the engine and is driven by a drive belt. If it's "squeeling," it usually means the drive belt is loose or glazed, but could also be a bad idler pulley bearing, as well.
Water pump? idler? pulleys or worse? - Nissan Forum
2009年1月20日 · Maybe the pulley locking up and the belt slipping on it? I did notice one of the pulleys (didn't note which one) had a shiny surface on the inside, so this may be it. I have seen some posts about pulling the tire and fender well to get better access to the components.