My take on Harbor Freight rotisserie, with some machining..
2015年8月12日 · This is using 2 Harbor Freight engine stands, and a 3rd one that a coworker had sitting in his yard. The machining content is that I purchased a piece of pipe and then turn down some 4140HT to make the part that spins. I used threaded rod as a means to level the car for some welding that I will have to do..
Harbor Freight Portapower Sets - Are They Worth Buying?
2007年3月21日 · I have the Harbor Freight 4-Ton set (Made in China, of course) and the Matco 10-Ton set (surprisingly, Made in Taiwain). The fit and finish of the Harbor Freight is pretty bad, as you would expect, and it leaks a lot, but it does work for the occasional garage job.
Harbor Freight "Alumiweld" - The Home Shop Machinist
2012年3月3日 · James the guy that does the demo's and sells it @ NAMES and car, motorcycle and other shows. I have used the stuff for 20 years it is about all the same alloy. The biggest thing he has told me is clean clean clean it has to be clean!
Has anyone used a Harbor Freight 110lb pressurized abrasive …
2021年12月9日 · I've been using that unit for a few years, and it works fine for me. I've done two frame off car restorations with it. I use common contractors sand, but do it on a tarp and reclaim most of it, so media cost is minimal. My compressor is 5 hp, 80 gal single stage, and keeps up if i don't use too big a nozzle.
Metal Cutting Circular Saw Blade - The Home Shop Machinist
2024年10月23日 · I bought a couple online to cut some 3/8” plate for a repair/modification to my 20 ton press. I wanted a clean edge so I didn’t have it cut with a torch. It was doing a great job and then my 19 year old Harbor Freight saw burst into flames! I am cheap so I went back to Harbor Freight and got a saw that draws 14 amps. The new
Lathe Bearings//Harbor Freight-Central Machinery 5980
Lathe Bearings//Harbor Freight-Central Machinery 5980 03-01-2015, 05:14 PM Yes, I'm a newbie at this, but after acquiring and putting in some new bearings in this simple old 3-in-1 I milled a few parts ( took forever), but I was able to use it for my …
Harbor freight spot welder won't work. - The Home Shop …
2012年1月26日 · Hello all ! I've been looking around here for a while. My first post. I'm a sheet metal guy who does a little mill a lathe work, as needed. But I mostly just do metal shaping. Anyhow, I'm looking for advise on a Harbor Freight spot welder that stopped working on me. It's the 220 model, was working fine, then it stopped. Acted like it had no power.
air compressor tripping on board breaker-diagnosis
2022年8月3日 · I just fixed my sons Harbor Freight compressor last week. It was doing the same thing. Tripping the onboard breaker. Motor seemed fine (no burned coils). I scrounged around in my junk box and found a capacitor that was at least close. Fixed the problem so yes, a bad cap will trip the breaker like that.
Harbor freight 42976 drill/mill machine question
2023年3月20日 · I believe the milling arbor is mt3 for harbor freights smaller 3-in-1 and its R8 for the 44142 model that I have which is the large 3-in-1. The lathe chuck bolts to a faceplate but the lathe thru hole accepts an mt4 also.
The tool store's gantry cranes, any difference?
After a lot of debate with myself, I got the Harbor Freight version. The primary reason I went with HF is that I needed to get it through an 8' garage door. While neither one will do that, only the HF model is designed such that I could (easily) cut it down to size.